How To Shingle Your Roof Like A Pro

shingling your roof
Shingling a Roof
Shingling or roof a home is a significant undertaking for a house owner as well as severe care is called for. This stated, a Do-It-Yourselfer homeowner can roof shingles or roofing system their own residence with a little expertise as well as the right devices. Or, if you’re in the area you could have the best roofers Bend has to offer do it for you. Your choice.
Needed Devices
In order to roof a home correctly and also securely the following tools are needed: Ladders, Roofing System Jacks, Hammer, Carpenters Knife, Chalk Line, and also preferably a compressor or nail weapon.
Estimating Products
Generally the roof is gauged in squares, where a “square” represents 100 square feet. There are eighty tiles in one square. Nonetheless, when you go to your neighborhood house enhancement shop roof shingles are typically marketed in packages. Normally 3 packages equal one square, nevertheless this can vary a little pending the tile design.
Measure the location of your roof covering (size x width) and also divide by 100 to obtain the number of squares called for. After that multiply this number by three to get the variety of packages of roof shingles needed for the job. Include an added 10-15% for extra, leaning toward the 15% if your roofing has hips and valleys.
Drip edge, ice as well as water shield, asphalt paper, flashing, roof nails, and also hip and ridge vents will additionally be needed. The Drip edge comes in numerous sizes. Action the outside perimeter of the roof covering to calculate the drip edge needed. The ice and water shield, asphalt paper and blinking come in roles. Utilize your roofing square location estimation for identifying your asphalt paper demands. Usually just one or 2 courses of ice and water guard is called for along the bottom/eave of the roofing and in the valleys. Compute 2 times the length of the roofing system and valleys to approximate the quantity of ice and water shield needed.
Normally each shingle will call for 4-6 roofing nails and also blinking generally can be found in 16″ large functions or 6×6 or 8×8 square inch steps. Action blinking is commonly utilized around smokeshafts, dormers as well as side wall junctions. Hip and also Ridge vent will vary with neighborhood building ordinance, nonetheless a harsh quote would certainly be to gauge the length of your roof’s hip as well as ridges and also take 75% of this number for computing the quantity of vent required.
You should currently have the ability to relatively accurately compute the price of product for roof your residence.
Installing the Drip Side
Nail the Drip edge around the whole outside border of the roof.
Use the Ice as well as Water Guard Membrane Layer and also the Asphalt Paper
Use the ice and also water shield material such that it is flush with the drip side. If the environment in your location has extreme winters and/or considerable yearly rains, add a 2nd program of ice and water guard for added protection. You should also add the ice as well as water shield membrane layer in the valleys.
Following apply the asphalt paper to the entire roofing, beginning with all-time low as well as working in the direction of the ridge. Make certain each training course of asphalt paper overlaps the reduced row by numerous inches (effectively shingling with the asphalt paper).
Set up steel blinking
Mount metal flashing in all of the valleys. Step blinking around chimneys and dormers will certainly be included as the shingles are set up.
Mounting the Shingles
Beginning the shingling at the end of the roofing (or at the eaves). Lay a starter course such that the bottom edge of the tile align purge with the drip edge. The starter strip is a “tabless” shingle that you make from the normal shingles using your carpenter’s knife.
Lay your next course of full roof shingles over the initial course, surprising the starter joints from the initial program to stop water penetration.
Keep in mind: Often you might wish to begin with a complete or a partial shingle at one end. In either case, you want to try to avoid little tile pieces at the far end of the roofing. To prevent this, separate the length of the roofing by the length of a full roof shingles and examine how much of a tile size you want to begin with. Ideally you do not intend to have pieces smaller than 12″.
Make Use Of a Chalk Line
To ensure your tile courses run straight use a chalk line. Step the ended up reveal on your tiles. Normally this is about 5 inches. Then make marks every 5 inches on the gable ends of the roofing. Break a chalk line in between the gable ends at each pair of marks right up the roof. This will certainly guarantee that you shingles run true as well as straight as you progress up the roofing system with the programs.
Vertical lines need to also be broken every 3 to 6 feet to ensure your tabs maintain placement.
Use of Roof Jacks
After 3 or 4 training courses of roof shingles have been mounted utilizing ladders, roof jacks may be needed to access the upper courses. Roofing jacks are steel brackets that hold planks in position for you to depend on. The roofing system jacks should be firmly nailed via the decking and also into rafters to make sure that they will support your weight.
Shingling Valleys, Chimneys, Skylights and also Dormers, and also Action Flashing
Shingling the valleys and also mounting blinking calls for added care. The shingles, typically originating from two converging training courses when entering a valley, need to overlap each other such that no water penetration happens.
Skylights, chimneys and dormers need to be action flashed (action flashing is interleaved with each training course of roof shingles) to ensure water is kept from permeating the roof covering.
Including the Ridge Vent and Caps
To finish the roof covering project, ridge vents require to be set up. These are toenailed to the top of the ridge and then capped.
The ridge cap avoids water from getting in the residence using the ridge air vent, while still allowing your house to breath. The ridge cap is created out of private shingle tabs that have their incomplete corners cut off at 45 degree angles. Each changed tile tab, is toenailed such that it overlaps the previous item as you work your means down the size of the ridge vent.

This article about shingling your roof was brought to you by the roofers over at…

Top Roofers Bend
61008 Creekstone Loop, Bend, OR 97702
(541) 460-7616